网上真人娱乐开户是一家集网上真人娱乐开户,网上真人娱乐开户,网上真人娱乐开户于一体的综合性娱乐公司,为玩家提供全方位的游戏体验,诚邀您的体验。

歡迎來到泰州福聲電子科技有限公司官方網站!
400-006-1982
產品中心
  • FST-9040

FST-9040

產品名稱 : FST-9040

類型 : 電磁式蜂鳴器

驅動方式 : 無源蜂鳴器

工藝 : 貼片蜂鳴器

尺寸范圍 : 5-10mm

詳細說明:

A. SCOPE 
This specification applies magnetic buzzer, FST-9040

B. SPECIFICATION

No.

Item

Unit

Specification

Condition

1

Oscillation Frequency

Hz

2700

Vo-p=1/2duty , square wave

2

Operating Voltage

Vo-p

2.5 ~ 4.5


3

Rated Voltage

Vo-p

3.6


4

Current Consumption

mA

MAX. 100

at Rated Voltage

5

Sound Pressure Level

dB

MIN. 85

at 10cm at Rated Voltage

6

Coil Resistance

Ω

16±3


7

Operating Temperature

-20 ~ +70


8

Storage Temperature

-30 ~ +80


9

Dimension

mm

Φ9.0 x H4.0

See appearance drawing

10

Weight (MAX)

gram

1.0


11

Housing Material


PPS( Black )


12

Leading Pin


 Plated Brass(Au)

See appearance drawing

13

Environmental  
Protection Regulation


 RoHS


 
C. APPEARANCE DRAWING  

 
Tol : ± 0.5      Unit: mm


D.TESTING METHOD    
Standard Measurement conditions
Temperature:25±2℃  Humidity:45-65%

Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the measuring instruments shown below
 
In the measuring test, buzzer is placed as follows:
 
 
E. Typical Frequency Response Curve
 
 

F. Recommend Driving Circuit 
 
The base current Ib should high enough so that it saturates the collector current of the transistor with the CB load.

 

G. Soldering Condition
(1)Recommendable reflow soldering condition is as follows
(Reflow soldering is twice)
Note:It is requested that reflow soldering should be executed after heat of product goes down to normal.

  Heat resistant line
(Used when heat resistant reliability test is performed)
(2)Manual soldering
   Manual soldering temperature 350 ℃ within 5 sec.

 

H. RELIABILITY TEST

NO.

ITEM

TEST CONDITION AND REQUIREMENT

1

High Temperature
Test (Storage)

After being placed in a chamber with 802℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

2

Low Temperature
Test (Storage)

After being Placed in a chamber with -302℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

3

Humidity Test

After being Placed in a chamber with 90-95% R.H. at 402℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

4

Temperature Cycle
Test

The part shall be subjected to 5 cycles. One cycle shall be consist of:
 
Allowable variation of SPL after test: 10dB.

5

Drop Test

Drop on a hard wood board of 4cm thick, any directions ,6 times, at the height of 75cm .
Allowable variation of SPL after test: 10dB.

6

Vibration Test

After being applied vibration of amplitude of 1.5mm with 10 to 55 Hz band of vibration frequency to each of 3 perpendicular directions for 2 hours .
Allowable variation of SPL after test: 10dB.

7

Solderability
Test

Lead terminals are immersed in rosin for 5 seconds and then immersed in solder bath of +3005℃ for 31 seconds .
90% min. lead terminals shall be wet with solder
(Except the edge of terminals).

8

Terminal Strength
Pulling Test

The force of 9.8N(1.0kg) is applied to each terminal in axial direction for 10 seconds.
No visible damage and cutting off.

TEST CONDITION. 
Standard Test Condition        :      a) Temperature : +5 ~ +35℃  b) Humidity : 45-85%        c) Pressure : 860-1060mbar 
Judgment Test Condition      :      a) Temperature : +25 ± 2℃    b) Humidity : 60-70%         c) Pressure : 860-1060mbar
 

I. PACKING STANDARD 


[返回]

收起
展開
  在線客服
网上真人娱乐开户 mg平台真人游戏在线 亚洲真人娱乐ag ag环亚真人游戏平台 mg真人平台注册 opus真人平台 AG8.AG亚游官网手机版 mg真人视讯欢迎您 国际棋牌游戏平台真人 ag捕鱼娱乐平台